Pennsylvania Code & Bulletin
COMMONWEALTH OF PENNSYLVANIA

• No statutes or acts will be found at this website.

The Pennsylvania Bulletin website includes the following: Rulemakings by State agencies; Proposed Rulemakings by State agencies; State agency notices; the Governor’s Proclamations and Executive Orders; Actions by the General Assembly; and Statewide and local court rules.

PA Bulletin, Doc. No. 22-313

PROPOSED RULEMAKING

ENVIRONMENTAL QUALITY BOARD

[25 PA. CODE CH. 109]

Safe Drinking Water PFAS MCL Rule

[52 Pa.B. 1245]
[Saturday, February 26, 2022]

 The Environmental Quality Board (Board) proposes to amend Chapter 109 (relating to safe drinking water) to read as set forth in Annex A. The proposed amendments will improve public health protection by setting maximum contaminant level goals (MCLG) and maximum contaminant levels (MCL) for two per- and polyfluoroalkyl substances (PFAS)—perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS).

 PFAS are considered emerging contaminants because research is ongoing to better understand the potential impacts PFAS pose to human and animal health and the environment. PFAS are potentially linked to a number of adverse health effects, including high cholesterol, developmental effects including low birth weight, liver toxicity, decreased immune response, thyroid disease, kidney disease, ulcerative colitis and certain cancers, including testicular cancer and kidney cancer.

 The proposed amendments are intended to protect public health by setting State MCLs for contaminants in drinking water that are currently unregulated at the Federal level. With the proposed amendments, the Commonwealth would move ahead of the United States (U.S.) Environmental Protection Agency (EPA) in addressing PFOA and PFOS in drinking water and join a small group of states that have set MCLs for select PFAS in drinking water. Currently, six states have set MCLs for one or more PFAS—Massachusetts, Michigan, New Hampshire, New Jersey, New York and Vermont.

 Safe drinking water is vital to maintaining healthy and sustainable communities. Proactively addressing PFOA and PFOS contamination in drinking water can reduce the incidence of illness and reduce health care costs. Recent research suggests that the EPA's Combined Lifetime Health Advisory Level (HAL) for PFOA and PFOS is not sufficiently protective against adverse health effects. The EPA has started the process of setting more stringent standards for PFOA and PFOS in drinking water, but that process is expected to take years to complete. For that reason, it is important that the Board act now to propose more protective standards for this Commonwealth, to protect the health of residents in this Commonwealth. Proper investment in public water system infrastructure and operations helps ensure a continuous supply of safe drinking water, enables communities to plan and build future capacity for economic growth, and ensures their long-term sustainability for years to come.

 The proposed PFOA and PFOS MCLs will apply to all 3,117 community, nontransient noncommunity, bottled, vended, retail and bulk water systems in this Commonwealth. Of these, 1,905 are community water systems, serving a combined population of approximately 11.4 million residents in this Commonwealth. Another 1,096 are nontransient noncommunity water systems serving approximately 507,000 persons.

 The proposed amendments also include minor revisions to address incorrect cross-references and citations, delete duplicated text and update language to be consistent with revisions made in the 2018 General Update of the Chapter 109 regulations. These minor updates are a codification of existing practices and will have no change from current practice.

 This proposed rulemaking was adopted by the Board at its meeting of November 16, 2021.

A. Effective Date

 This proposed rulemaking will go into effect upon final-form publication in the Pennsylvania Bulletin. Initial compliance monitoring for community and nontransient noncommunity water systems serving a population of greater than 350 persons and all bottled, vended, retail and bulk systems begins January 1, 2024; initial monitoring for community and nontransient noncommunity water systems serving a population of less than or equal to 350 persons begins January 1, 2025.

B. Contact Persons

 For further information, contact Lisa D. Daniels, Director, Bureau of Safe Drinking Water, P.O. Box 8467, Rachel Carson State Office Building, Harrisburg, PA 17105-8467, (717) 787-9633; or Leda J. Lacomba, Assistant Counsel, Bureau of Regulatory Counsel, P.O. Box 8464, Rachel Carson State Office Building, Harrisburg, PA 17105-8464, (717) 787-7060. Information regarding submitting comments on this proposed rulemaking appears in section I of this preamble. Persons with a disability may use the Pennsylvania Hamilton Relay Service at (800) 654-5984 (TDD users) or (800) 654-5988 (voice users). This proposed rulemaking is available electronically through the Department of Environmental Protection's (Department) web site at www.dep.pa.gov (select ''Public Participation,'' then ''Environmental Quality Board,'' and then navigate to the Board meeting of November 16, 2021).

C. Statutory Authority

 This proposed rulemaking is being made under the authority of section 4 of the Pennsylvania Safe Drinking Water Act (act) (35 P.S. § 721.4), which grants the Board the authority to adopt rules and regulations governing the provision of drinking water to the public, and section 1920-A of The Administrative Code of 1929 (71 P.S. § 510-20), which authorizes the Board to promulgate rules and regulations necessary for the performance of the work of the Department.

D. Background and Purpose

 PFAS are a large class of man-made synthetic chemicals that were created in the 1930s and 1940s for use in many industrial and manufacturing applications. It is estimated that the PFAS family includes more than 6,000 chemical compounds. PFAS have been widely used for their unique properties that make products repel water, grease and stains, reduce friction and resist heat. PFAS are found in industrial and consumer products such as clothing, carpeting, upholstery, food packaging, non-stick cookware, fire-fighting foams, personal care products, paints, adhesives, metal plating, wire manufacturing and many other uses. Because of their unique chemical structure, PFAS readily dissolve in water and are mobile, are highly persistent in the environment and bioaccumulate in living organisms over time.

 Decades of widespread use of products containing PFAS has resulted in elevated levels of environmental pollution and exposure in some areas of the State. PFAS remain in the environment and cycle through various media (air, water, soil) depending on how and where the substances were released. The primary means of distribution of PFAS throughout the environment has been though the air, water, biosolids, food, landfill leachate and fire-fighting activities. For a diagram showing the PFAS cycle and its exposure pathways, refer to the Department's PFAS webpage at www.dep.pa.gov/Citizens/My-Water/drinking_ water/PFAS/Pages/DEP-Involvement.aspx.

 The Department's Safe Drinking Water Program first became aware of PFAS as emerging contaminants in 2013 when the EPA included six PFAS in its Third Unregulated Contaminant Monitoring Rule (UCMR3). The six PFAS included in UCMR3 monitoring are PFOA, PFOS, perfluorononanoic acid (PFNA), perfluorohexanesulfonic acid (PFHxS), perfluoroheptanoic acid (PFHpA), and perfluorobutanesulfonic acid (PFBS). The UCMR rules are Federal direct-implementation rules that are updated every 5 years to require monitoring for up to 30 unregulated contaminants to generate National occurrence data and inform the Federal regulatory determination process. Public water systems (PWS) serving more than 10,000 people and a select number of smaller PWSs were required to monitor for PFAS and other contaminants during 2013—2015 for UCMR3. In this Commonwealth, a total of 175 systems conducted PFAS monitoring for UCMR3; of these systems, PFAS was detected at 6 systems above the 2009 Provisional Health Advisory Levels (HAL) for PFOA and PFOS of 400 nanograms per liter (ng/L) or parts per trillion (ppt) and 200 ng/L, respectively. The Department worked closely with the EPA and the PWSs to address the elevated levels of PFAS found during the UCMR3 monitoring.

 In May of 2016, the EPA issued the Final HAL for PFOA and PFOS as a Combined Lifetime HAL of 70 ng/L. At that time, the Department began implementing the EPA's Combined Lifetime HAL of 70 ng/L for PFOA and PFOS using existing authority under the act and Chapter 109 regulations. PWSs that exceed the HAL are required to conduct follow-up and corrective actions to protect public health, including the following actions:

 • One-hour reporting of sample results to the Department to ensure timely consultation and oversight regarding investigative and corrective actions (§ 109.701(a)(3)(iii) (relating to reporting and recordkeeping)),

 • Collection of confirmation samples (§ 109.302 (relating to special monitoring requirements)),

 • Issuance of Tier 2 Public Notice to consumers (§ 109.409 (relating to Tier 2 public notice—categories, timing and delivery of notice)),

 • Quarterly monitoring at the entry point to track levels of contamination (§ 109.302), and

 • If levels continue to exceed the HAL, taking additional actions as needed to protect public health such as taking contaminated sources off-line or installing treatment (§ 109.4 (relating to general requirements)).

PFAS action team

 In the absence of Federal action to address PFAS, Governor Tom Wolf signed Executive Order 2018-08 (EO) on September 19, 2018. The EO created the PFAS Action Team, a multi-agency group tasked with, among other things, developing a comprehensive response to identify and eliminate sources of contamination, ensure drinking water is safe, manage environmental contamination, review gaps in data and oversight authority, and recommend actions to address those gaps. The PFAS Action Team released its Initial Report in December of 2019 to the Department's PFAS webpage at www.dep.pa.gov/pfas. The report includes information about PFAS, challenges associated with managing contamination, actions taken to date and recommendations for future actions. Recommendations include additional funding for communities dealing with PFAS contamination and strengthened statutory authorities to adequately address PFAS.

 In 2019, the Department's Safe Drinking Water Program moved forward with two key projects to advance its knowledge of PFAS—the PFAS Sampling Plan and PFAS Toxicology Services Contract.

PFAS Sampling Plan

 The PFAS Sampling Plan was developed and posted to the Department's PFAS webpage at www.dep.pa.gov/Citizens/My-Water/drinking_water/PFAS/Pages/DEP-Involvement.aspx in April of 2019. The plan was intended to prioritize PWS sites for PFAS sampling and generate Statewide occurrence data. Several factors were considered in developing the targeted plan, including:

 • Identification of ''potential sources of PFAS contamination'' (PSOC) based on a literature review,

 • Identification of PWS sources located within 1/2 to 3/4 of a mile from PSOCs, and

 • Selection of PWS sources to serve as a control or baseline group.

 The selection process involved a combination of spatial analysis and programmatic review. The spatial analysis included the creation of a Geographic Information System (GIS) project using ArcMap 10.4.1 that focused on PWS source locations and information about PSOCs. The sampling pool was prioritized based on relative risk and included community water systems and nontransient noncommunity water systems.

 To prioritize sampling, the selection process included an assessment of the potential risk from nearby PSOCs. Several layers containing locational and other information specific to PSOCs were created or otherwise included in the GIS. These layers include the following industries and land uses:

 • Military bases

 • Fire training schools/sites

 • Airports

 • Landfills

 • Manufacturing facilities (apparel, chemicals, electronics, fabricated metal, paper products, textiles and leather, upholstered furniture)

 • State Hazardous Sites Cleanup Act sites, the EPA Superfund sites and other known PFAS-contamination sites

 The sampling plan includes details about the sources of GIS data and multiple maps that indicate the locations and prevalence of the PSOCs and the locations of the targeted and baseline sampling sites.

 Based on the compilation of PSOCs, the information was used to select PWS sources that are located within 1/2 to 3/4 of a mile of a PSOC. The initial sampling pool included 493 PWS sources. The sampling pool contained a mix of PWS types and sizes and provided a good spatial distribution across the State. Based on available funding of $500,000, the Department proposed sampling at 360 targeted and 40 baseline entry point (EP) sites. Baseline sources are located in a HUC-12 watershed (a watershed assigned a 12-digit hydrologic unit code, or HUC, by the United States Geological Survey) with at least 75% forested land and at least 5 miles from a PSOC. Ultimately, samples were collected from 412 EPs including 372 targeted sites and 40 baseline sites. Note that an EP to the distribution system may include water from more than one source of supply.

 Sampling and analysis began during the Summer of 2019 using EPA Method 537 and a PA-accredited lab to analyze samples for the six UCMR3 PFAS. However, in early 2020, the Department took the opportunity to modify its analysis of samples by switching to EPA Method 537.1, which expanded the collection of occurrence data to 18 PFAS and adding the Department's Bureau of Laboratories for analysis. For consistency purposes, the Department repeated the sampling and analysis that had been conducted in 2019. Sampling was temporarily suspended from March 2020 to July 2020 due to the novel coronavirus (COVID-19) pandemic and resulting business closures and travel restrictions established under the Governor's Emergency Declaration. Sampling resumed in August 2020 and was completed at the end of March 2021, with the final sample results posted to the Department's PFAS webpage in June 2021. Table 1 includes a summary of the results from the PFAS Sampling Plan for the same six PFAS that were sampled under UCMR3.


Table 1. Summary of PFAS Sampling Plan results. Full results available at www.dep.pa.gov/pfas

Summary of PFAS Sampling Plan Results
PFOAPFOSPFNAPFHxSPFHpAPFBSUnits
Total No. Samples412412412412412412
Average2.02.50.41.40.71.1ng/L
Median0 (ND)0 (ND)0 (ND)0 (ND)0 (ND)0 (ND)ng/L
Minimum0 (ND)0 (ND)0 (ND)0 (ND)0 (ND)0 (ND)ng/L
Maximum59.6187.118.1140.032.664.0ng/L
No. and % of Detects  112 (27%)  103 (25%)  23 (6%  )52 (13%)  49 (12%)  66 (16%)  
Avg Detect Value7.59.97.210.96.17.0ng/L
Med Detect Value5.36.55.64.54.54.2ng/L
Min Detect Value1.71.81.81.91.81.7ng/L
Max Detect Value59.6187.118.1140.032.664.0ng/L

 For example, of the 412 samples analyzed for PFOA, 112 (27%) resulted in detectable concentrations of PFOA. The remaining 300 samples resulted in no detectable concentrations of PFOA. For the 112 samples in which PFOA was detected, the average detected value was 7.5 ng/L, the median detected value was 5.3 ng/L, the minimum detected value was 1.7 ng/L, and the maximum detected value was 59.6 ng/L.

 At the sampling sites with detections, 8 of the 18 PFAS included in EPA Method 537.1 were detected. The eight PFAS that were detected are: PFOA, PFOS, PFNA, PFHxS, PFHpA, PFBS, perfluorohexanoic acid and perfluoroundecanoic acid. Of the PFAS detected, PFOA and PFOS were most common, detected at 112 (or 27%) and 103 (or 25%) sites, respectively. Of the 412 total samples, 2 of the results were above the EPA's HAL of 70 ng/L for the combined concentrations of PFOA and PFOS. Results were nondetect at all 412 sites for the other 10 PFAS that were tested.

 Additionally, there are 23 results with detections from UCMR3 monitoring that were also included in the occurrence data evaluation. Because the reporting limits used for UCMR3 monitoring (40 ng/L for PFOA and 20 ng/L for PFOS) were much higher than current reporting limits (which are generally below 5 ng/L), the Department did not include UCMR3 data that was below the UCMR3 reporting limits.

 Therefore, the Department used results from a total of 435 sampling sites in the evaluation of occurrence data.

PFAS Toxicology Services Contract

 In December 2019, the Department's Safe Drinking Water Program executed a toxicology services contract with Drexel University to: review other state and Federal agency work on MCLs; independently review the data, science and studies; and develop recommended MCLGs for select PFAS. MCLGs are nonenforceable, developed solely based on health effects and do not take into consideration other factors, such as technical limitations and cost. MCLGs are the starting point for determining MCLs.

 Deliverables were completed in January 2021 and include the ''Drexel PFAS Workbook'' and ''MCLG Drinking Water Recommendations for PFAS in the Commonwealth of PA'' (MCLG Report), available at the following links: Workbook, https://files.dep.state.pa.us/PublicParticipation/Public %20Participation%20Center/PubPartCenterPortalFiles/ Environmental%20Quality%20Board/2021/June%2015/ 03_PFAS%20Petition/01b_App%202%20Drexel%20PFAS %20Workbook%20January%202021.pdf and Report, https://files.dep.state.pa.us/PublicParticipation/Public%20 Participation%20Center/PubPartCenterPortalFiles/Environmental%20Quality%20Board/2021/June%2015/ 03_PFAS%20Petition/01a_App%201%20Drexel%20PFAS %20Report%20January%202021.pdf. The MCLG Report was developed by the Drexel PFAS Advisory Group (DPAG)—a multidisciplinary team of experts in toxicology, epidemiology, and drinking water standards and risk assessment. The DPAG reviewed pertinent literature and work across the country and independently developed recommended MCLGs based on non-cancer endpoints. The MCLG Report discusses relevant inputs and includes a summary table for each PFAS that documents the development of the recommended MCLG. Table 2 includes the Reference Dose and recommended Chronic Non-Cancer MCLG for each PFAS that was reviewed.

Table 2. DPAG Reference Dose and Recommended Chronic Non-Cancer MCLGs.

DPAG Reference Dose and Recommended Chronic Non-Cancer MCLGs
PFASReference Dose
(ng/kg/day)
MCLG
(ng/L or ppt)
PFOA3.98
PFOS3.114
PFNA2.26
PFHxS4.020
PFHpANone derived*8
PFBS3955
GenX (HFPO-DA)75108

 *Reference dose was not derived due to a lack of evidence on its toxicity. Recommended MCLG is based on its chemical structure.

 As the DPAG explains in its MCLG Report, it ''reviewed a number of recommendations made by EPA and State agencies that chose to create a summative approach to PFAS, combining multiple minimal risk levels or advisory levels into one cumulative drinking water value. No clear consensus exists on this approach and the use of the summative approach was clearly designed to be a shortcut based on a presumption that the agents all have similar health effects and end points. While this approach may work for other toxins such as dioxins, furans, and coplanar polychlorinated biphenols, it does not appear to be based on evidence available for PFAS. The DPAG therefore committed early in the process to developing an individual MCLG for each of the requested PFAS.'' (DPAG, January 2021)

 The DPAG further describes in the MCLG Report that ''For each of the PFAS studied, the DPAG identified points of departure (POD) and rationale for selection from risk assessments published by other States, the EPA and ATSDR (Agency for Toxic Substances and Disease Registry). DPAG then assessed the underlying critical studies driving the selection of the POD. Every effort was made to use the experience and published findings from other agencies and build and refine on these as much as possible into a best practice approach.'' (DPAG, January 2021)

 In the ''Drexel PFAS Workbook,'' the DPAG explains how threshold levels (such as advisory levels, MCLGs, MCLs) are generally determined, although each state's process can vary. Table 3, taken from the workbook, is a helpful tool in understanding the process. More detail about the DPAG's determination of MCLGs can be found as follows, under the subsections for PFOA and PFOS.


Table 3. How POD is Used to Calculate Reference Dose (RfD) and Threshold Level (DPAG, June 2020)

PFOA
US EPA
Office of Water 2016
Standard / GuidanceHealth Advisory
Media TypeDrinking Water
Threshold Level (ug/L) or (PPT)0.07 ug/L 70 PPT (PFOA + PFOS cannot exceed this level)
Key Study Information
Critical Effect Key Study Reference1Developmental (reduced ossification, accelerated puberty) Lau, C., J.R. Thibodeaux, R.G. Hanson, M.G. Narotsky, J.M. Rogers, A.B. Lindstrom, and M.J. Strynar. 2006. Effects of perfluorooctanoic acid exposure during pregnancy in the mouse. Toxicological Science 90:510—518.
SpeciesMice
Study Exposure Duration (days)17 days
Kinetics
Method of Administered Dose conversion to Internal Serum LevelModeled AUC
Method to Derive Human Equivalent DoseDose adjustment factor of 0.00014 L/kg-day, based on first order kinetic clearance rate (Vd x (ln 2 ÷ t))
Dose-Response
Dose Response Modeling MethodLOAEL
POD2 38 mg/L
POD x DAF = Human Equivalent Dose30.0053 mg/kg/day
Uncertainty Extrapolation
Human Variability (UFH)10
Animal to Human (UFA)3
Subchronic to Chronic (UFS)1
LOAEL to NOAEL (UFL)10
Database (UFD)1
Total Composite (UFT)300
HED/UFT= Reference Dose (mg/kg-day)4(2 x 10-5 mg/kg-day) or 20 ng/kg/d
ReceptorLactating women
Exposure
Ingestion Rate (L/day)
Body Weight (Kg)
Normalized Drinking Water Intake (L/kg-day)0.054
Relative Source Contribution20%
Threshold Level (ug/L) or (PPT)50.07 ug/L 70 PPT (PFOA + PFOA cannot exceed this level)
Additional Information90th percentile consumers only estimate of combined direct and indirect community water ingestion for lactating women (see Table 3-81 in USEPA 2011b).
ReferenceHealth Effects Support Document for Perfluorooctanoic Acid, U.S. Environmental Protection Agency Office of Water (4304T) Health and Ecological Criteria Division, EPA Document Number: 822-R-16-003. May 2016. And Drinking Water Health Advisory for Perfluorooctanoic Acid, U.S. Environmental Protection Agency Office of Water (4304T) Health and Ecological Criteria Division, EPA Document Number: 822-R-16-005. May 2016 https://www.epa.gov/ground-water-and-drinking-water/drinking-water-
health-advisories-pfoa-and-pfos

Footnotes:

1 Critical effect selected

2 Point of Departure (POD) determined by critical review of study

3 POD adjusted by using preferred methods to derive Human Equivalent Dose (HED)

4 HED divided by Uncertainty Factors (UF) to achieve Reference Dose (RfD) in target population

5 Final adjustment made based on intake to derive Threshold Level (e.g. MCL, MCLG, HAL, etc.)

 Following completion of these two key projects—the PFAS Sampling Plan and the PFAS Toxicology Services Contract—the Department's Safe Drinking Water Program moved forward with developing a proposed PFAS MCL rule.

MCL rulemaking process

 The Department must follow a rigorous process when setting an MCL. An MCL rulemaking must be based on available data, studies, and science, and must consider all factors as required by the Federal Safe Drinking Water Act (Federal Act) (42 U.S.C.A. §§ 300f—300j-27) and the Commonwealth's Regulatory Review Act (RRA) (71 P.S. §§ 745.1—745.14). Among other things, the Department must consider the following:

 • Health effects,

 • Occurrence data,

 • Technical limitations such as available analytical methods and detection and reporting limits,

 • Treatability of the contaminant and available treatment technologies, and

 • Costs and benefits. (71 P.S. § 745.5b).

 In addition to State requirements, the Department needs to consult the Federal Act and its implementing regulations. See 42 U.S.C.A. §§ 300f—300j-9; see also 40 CFR Parts 141, 142 and 143 (relating to National Primary Drinking Water Regulations; National Primary Drinking Water Regulations Implementation; and Other Safe Drinking Water Act Regulations). The EPA explains how the agency sets standards at the following link: www.epa.gov/sdwa/how-epa-regulates-drinking-water-contaminants. In establishing the MCLs in this proposed rulemaking, the Department was informed by the EPA's procedure to establish an MCL. It is important for the Department to understand the EPA's process of setting an MCL because similar criteria are required of the Department under the RRA and because the MCLs in this proposed rulemaking are the first MCLs that the Department has set; every other MCL in effect in this Commonwealth was set by the EPA and incorporated by reference into the Department's Chapter 109 regulations. In addition, to retain primacy for implementing the Federal Act in this Commonwealth, the Department's standard setting process must be at least as stringent as the Federal process.

 After reviewing health effects data, the EPA sets an MCLG. MCLGs are nonenforceable public health goals. MCLGs consider only public health and not the limits of detection and treatment technology effectiveness. Therefore, MCLGs sometimes are set at levels which water systems cannot meet because of technical limitations.

 Once the MCLG is determined, the EPA sets an enforceable standard. In most cases, the standard is an MCL. The MCL is set as close to the MCLG as feasible. Taking cost into consideration, the EPA must determine the feasible MCL.

 As a part of the rule analysis, the Federal Act requires the EPA to prepare a health risk reduction and cost analysis in support of any standard. The EPA must analyze the quantifiable and nonquantifiable benefits that are likely to occur as the result of compliance with the proposed standard. The EPA must also analyze increased costs that will result from the proposed drinking water standard. In addition, the EPA must consider incremental costs and benefits associated with the proposed alternative MCL values. Where the benefits of a new MCL do not justify the costs, the EPA may adjust the MCL to a level that maximizes health risk reduction benefits at a cost that is justified by the benefits.

 The amendments to Chapter 109 in this proposed rulemaking include new MCLGs and MCLs for PFOA and PFOS. The amendments also include the provisions necessary to comply with the MCLs, including requirements for monitoring and reporting, public notification, consumer confidence reports, acceptable treatment technologies and analytical requirements.

 The Department is proposing to not move forward with an MCL for other PFAS at this time due to the reasons outlined in Table 4.


Table 4. Reasons for not moving forward with MCLs for other PFAS.

PFNA PFHxS PFHpA PFBS HFPO-DA 
Lack of occurrence data > MCLGxxxx
Incomplete cost/benefit data and analysisxxxxx
Reference dose was not derived due to lack of evidence on its toxicity x
Lack of treatability datax

 The decision to not move forward with MCLs for additional PFAS at this time is further supported by a review of co-occurrence data. This review considers the frequency with which individual PFAS detections co-occurred with other PFAS detections in the occurrence data set used for this proposed rulemaking. Based on an analysis of co-occurrence data, only 3.7% of all sites (or 16 out of 435 sites) had detections of at least 1 other PFAS at a level greater than its recommended MCLG when PFOA or PFOS levels did not exceed the proposed MCLs. In other words, the PFOA and PFOS proposed MCLs appear to be protective of other PFAS at least 96.3% of the time.

PFOA

PFOA—DPAG development of MCLG

 After a literature search and a review of the available evidence and recommendations from various agencies, the DPAG developed an MCLG recommendation for PFOA of 8 ng/L or ppt based on non-cancer endpoints. The DPAG determined that the most relevant inputs were from the EPA, ATSDR, Minnesota Department of Health (MDH), New Jersey Department of Environmental Protection and Michigan Department of Health and Human Services (MDHHS).

 The DPAG selected Koskela, et al. (2016) and Onishchenko, et al. (2011) as the critical studies, which identified developmental effects (including neurobehavioral and skeletal effects) as critical. The DPAG adopted the ATSDR's estimated Point of Departure (POD) of 8.29 mg/L. The DPAG followed the approaches used by MDHHS, MDH and ATSDR to select and determine the HED, UF, RfD, Relative Source Contribution (RSC) and recommended MCLG. Table 5 provides a summary of the DPAG's derivation of the MCLG for PFOA.

Table 5. DPAG Derivation of PFOA MCLG (DPAG, January 2021)

PFOA
Drexel PFAS Advisory Group (DPAG) 2021
Dose Response
Modeling Method
LOAEL
POD The average serum concentration was estimated in the mice (8.29 mg/L) using a three-compartment pharmacokinetic model (Wambaugh et al. 2013) using animal species, strain, sex-specific parameters. (ATSDR 2018)
HED = POD x DAF (mg/kg/d)DAF = Ke x Vd
Ke = 0.000825175 (8.2 x 10-4) based on a human serum half-life of 840 days
(Bartell et al. 2010)
Vd = 0.17 L/kg (Thompson et al. 2010)
HEDLOAEL = PODLOAEL x DAF
HEDLOAEL = PODLOAEL x Ke x Vd
HEDLOAEL = 8.29 mg/L x 0.0000825175 x 0.17 L/kg
HEDLOAEL = 0.001163 mg/kg/d or 1.163 x 10-3 mg/kg/d
Uncertainty Extrapolation
Human Variability (UFH)10 (standard)
Animal to Human (UFA)3 (DAF applied)
Subchronic to Chronic (UFS)1 (Chronic effect studied)
LOAEL to NOAEL (UFL)10 (standard)
Database (UFD)1
Total Composite (UFT)300
RfD = HED/UFT (mg/kg/d)RfD = 0.001163 mg/kg/d/300
RfD = 3.9 ng/kg/day (3.9 x 10-6 mg/kg/d)
THSV = POD / UFT THSV= 8.29 mg/L/ 300
THSV= 0.028 mg/L
ReceptorInfant exposure via breastmilk for 1 year, from mother chronically exposed via water, followed by lifetime of exposure via drinking water. Protective for short-term, subchronic and chronic. (also protective of formula fed infant). Goeden Model Parameters: Placental transfer of 87% and breastmilk transfer of 5.2% (MDH (2020 PFOA)). The Human Serum half-life is set at 840 days (Bartell et al. 2010). The Volume of distribution of 0.17 L/kg (Thompson et al. [2010]) Other factors include, 95th percentile drinking water intake, consumers only, from birth to more than 21 years old. Upper percentile (mean plus two standard deviations) breastmilk intake rate. Time-weighted average water ingestion rate from birth to 30-35 years of age is used to calculate maternal serum concentration at delivery. (Goeden et al. [2019]) A Relative Source Contribution of 50% (0.5) is applied and based on studies which showed that infants RSC is similar to NHANES 95th percentiles for 3-11 (2013-2014) and over 12 years old (2015-2016) participants. (CDC 2019)
Chronic Non-Cancer MCLG The model produces a Chronic Non-Cancer MCLG of 8 ng/L (ppt). This protects health during the growth and development of a breast fed infant.

 In summary, the DPAG recommended a chronic non-cancer MCLG for PFOA of 8 ng/L to protect breast-fed infants and throughout life.

 The Board is proposing to set the MCLG for PFOA at the DPAG recommended level of 8 ng/L.

PFOA—occurrence data

 Table 6 is a summary of occurrence data for PFOA. The data includes 412 results from the PFAS Sampling Plan and detect data from 23 sites under UCMR3 for a total of 435 sample results.

Table 6. PFOA Occurrence Data > MCLG of 8 ng/L

PFOA Occurrence Data > Proposed MCLG of 8 ng/L
# of sites (of 435) > MCLG46
% of sites > MCLG10.6%
Estimated # of EPs (of 3785) > MCLG400

 A review of occurrence data indicates that 46 EPs out of a total number of 435 EPs sampled exceeded the proposed MCLG for PFOA of 8 ng/L. This represents 10.6% of all EPs sampled. This exceedance rate may overestimate the exceedance rate for other PWSs in this Commonwealth that were not sampled because the occurrence data sampling predominately targeted sites near potential sources of PFAS contamination. However, the occurrence data provides the most relevant information currently available on the prevalence and levels of PFAS in PWSs in this Commonwealth. Applying the occurrence data PFOA MCLG exceedance rate (10.6%) to the total number of EPs for all applicable PWSs (3,785 EPs), it is estimated that 400 EPs will exceed the proposed MCLG of 8 ng/L.

PFOA—proposed MCL of 14 ng/L

 The Board is proposing an MCL of 14 ng/L for PFOA. The proposed MCL is based on the health effects and proposed MCLG, occurrence data, technical feasibility, and costs and benefits.

 Table 7 is a summary of occurrence data for PFOA when compared to the proposed MCL of 14 ng/L.

Table 7. PFOA Occurrence Data > MCL of 14 ng/L

PFOA Occurrence Data > Proposed MCL of 14 ng/L
# of sites (of 435) > MCL25
% of sites > MCL5.7%
Estimated # of EPs (of 3785) > MCL218

 A review of occurrence data indicates that 25 EPs out of a total number of 435 EPs sampled exceeded the proposed MCL for PFOA of 14 ng/L. This represents 5.7% of all EPs sampled. This exceedance rate may overestimate the exceedance rate for other PWSs in this Commonwealth that were not sampled because the occurrence data sampling predominately targeted sites near potential sources of PFAS contamination. However, the occurrence data provides the most relevant information currently available on the prevalence and levels of PFAS in PWSs in this Commonwealth. Applying the occurrence data PFOA MCL exceedance rate (5.7%) to the total number of EPs for all applicable PWSs (3,785 EPs), it is estimated that 218 EPs will exceed the proposed MCL of 14 ng/L.

 Treatment cost estimates were determined based on a survey conducted of systems in this Commonwealth with existing PFAS treatment and of PFAS treatment manufacturers, an American Water Works Association published PFAS Case Study and from information provided by members of the Association of State Drinking Water Administrators (ASDWA). Costs were provided for granular activated carbon (GAC), anion exchange (IX) and reverse osmosis (RO). The RO costs were not included in the final cost estimates because, due to wastewater disposal requirements, the technology is currently impractical. Additionally, the costs for GAC, IX and RO provided from the vendors were excluded from the final cost estimates because they were limited to media costs and did not include the infrastructure requirements.

 Treatment capital costs were normalized to construction costs for treating 1 million gallons per day (MGD).

 • The average capital cost for the GAC treatment was $3,457,110 per MGD per EP with an average annual operation and maintenance (O&M) cost of $171,970 per MGD per EP.

 • The average capital cost for the IX treatment was $3,284,360 per MGD per EP with an average annual O&M cost of $155,666 per MGD per EP.

 • The average capital cost for using either GAC or IX treatment is $3,370,735 per MGD per EP with an average annual O&M cost of $163,818 per MGD per EP.

 • Annualized over 20 years at a 4% interest rate, the average annual capital cost for either GAC or IX treatment is $248,025 per MGD per EP.

 Following is a summary of the estimated costs and benefits associated with the proposed MCL for PFOA of 14 ng/L. Section F of this preamble presents additional information on the costs and benefits of this proposed rulemaking. Treatment cost estimates are based on the costs to install and maintain treatment for a 1 MGD treatment plant. The actual costs would be expected to be proportionally less for a treatment plant with a smaller design capacity. For example, the average design capacity for small systems is 100,000 gallons per day, which is 1/10 of 1 MGD (that is, 0.1 MGD); treatment cost estimates for a small system with a design capacity of 0.1 MGD would be 1/10 of the cost estimates presented as follows.

 • Estimated costs:

 ◦ Estimated average annual compliance monitoring costs (@ $616/EP/Quarter) = $2.9 M

 ◦ Estimated average annual treatment costs (average of GAC and IX) = $89.8 M per MGD + estimated annual performance monitoring costs = $4.8 M

 • Estimated annual treatment capital costs, annualized over 20 years at 4% interest = $248,025 per MGD per EP × 218 EPs = $54.1 M per MGD

 • Estimated annual treatment O&M costs = $35.7 M per MGD + estimated annual performance monitoring costs = $4.8 M

 • Estimated annual treatment O&M costs = $163,818 per MGD per EP × 218 EPs = $35.7 M per MGD

 • Estimated annual performance monitoring costs = $616 per sample per EP × 36 samples = $22,176 per EP × 218 EPs = $4.8 M

 ◦ Estimated total annual costs = $89.8 M per MGD in treatment costs + $7.7 M in compliance monitoring and performance monitoring costs

 • Estimated benefits:

 ◦ 90% improvement in health protection as compared to current EPA HAL of 70 ppt

 Table 8 provides a comparison of annual costs and benefits for the proposed MCL for PFOA of 14 ng/L, EPA's HAL of 70 ng/L, and other values considered for the proposed MCL. Performance monitoring costs are considered part of treatment O&M costs because performance monitoring is used to make operational decisions, such as when to change out treatment media.


Table 8. PFOA Comparison of Annual Costs and Benefits

PFOA Annual Costs and Benefits Analysis
Value (ng/L)Estimated
# of EPs
(of 3,785)
> Value
Compliance Monitoring Costs (Millions) Treatment O&M Costs Treatment Capital Costs (Millions) per MGD* annualized over 20 yearsTotal Costs (Millions)% Increase in Cost Compared to HAL% Improvement in Health Protection Compared to HAL
Treatment O&M Costs (Millions) per MGD*Performance Monitoring Costs (Millions)
HAL = 7058$2.46$9.50$1.29$14.39$27.630%0%
3578$2.56$12.78$1.73$19.35$36.4132%56%
20200$2.73$32.76$4.44$49.60$89.53224%80%
MCL = 14218$2.89$35.71$4.83$54.07$97.51253%90%
12270$2.97$44.23$5.99$66.97$120.15335%93%
10313$3.07$51.28$6.94$77.63$138.92403%96%
MCLG = 8400$3.39$65.53$8.87$99.21$177.00541%100%

 *For purposes of totaling annual costs, the costs that vary with design capacity (treatment O&M and treatment capital costs) were multiplied by a benchmark design capacity of 1 MGD.

 In evaluating the costs and benefits, the Department's goal was to provide at least a 90% reduction in adverse health effects (a 90% improvement in health protection) when compared to the HAL of 70 ng/L. This goal is consistent with several existing drinking water standards including the following standards:

 • the requirement to achieve at least a 90% inactivation of Giardia cysts using disinfection processes within a filtration plant (§ 109.202(c)(1)(ii) (relating to State MCLs, MRDLs and treatment technique requirements) regarding treatment technique requirements for pathogenic bacteria, viruses and protozoan cysts);

 • the use of the 90th percentile lead and copper levels when determining compliance with the lead and copper action levels of 0.015 mg/L and 1.3 mg/L, respectively (§ 109.1102(a) (relating to action levels and treatment technique requirements) regarding action levels for lead and copper), and

 • the requirement to meet the filtered water turbidity standards in 95% of measurements taken each month (§ 109.202(c)(1)(i)).

 As shown in Table 8 and Figure 1, additional improvement in public health benefits at PFOA values lower than the proposed MCL of 14 ng/L would require increasingly steep costs. For example, compared with the proposed MCL of 14 ng/L, an MCL value of 10 ng/L is estimated to achieve an additional 6% increase at an additional annual cost of approximately $41.4 million (Table 8, Figure 1), which is a rate of approximately $7 million in additional annual costs for every additional 1% of benefits. Compared with the HAL, the proposed MCL of 14 ng/L is estimated to achieve a 90% improvement in public health benefits at an additional annual cost of roughly $70 million, which is a rate of approximately $0.8 million in additional annual costs for every additional 1% of benefits.

Figure 1. Annual Total Costs and Benefits (% Health Protection Improvement) at Various PFOA levels

 For the aforementioned reasons, the Department believes that the proposed MCL for PFOA of 14 ng/L strikes an appropriate balance between the benefits (90% improvement in public health) and costs (253% increase in costs) when compared to the benefits and costs associated with meeting the HAL of 70 ng/L.

PFOS

PFOS—DPAG development of MCLG

 After a literature search and a review of the available evidence and recommendations from various agencies, the DPAG developed an MCLG recommendation for PFOS of 14 ng/L or ppt based on non-cancer endpoints. The DPAG referenced inputs from the EPA, ATSDR, MDH and MDHHS.

 The DPAG selected Dong, et al. (2011) as the critical study, which identified immunotoxicity effects (including immune suppression) as critical. The DPAG determined that a POD of 2.36 mg/L is appropriate. The DPAG followed the approaches used by MDHHS, MDH and the EPA to select and determine the HED, UF, RfD, RSC and recommended MCLG. Table 9 provides a summary of the DPAG's derivation of the MCLG for PFOS.

Table 9. DPAG Derivation of PFOS MCLG (DPAG, January 2021)

PFOS
Drexel PFAS Advisory Group (DPAG) 2021
Dose Response Modeling MethodNOAEL
POD 2.36 µg/mL (or 2.36 mg/L)
HED = POD x DAF (mg/kg/d)Toxicokinetic Adjustment based on Chemical- Specific Clearance Rate (Li et al 2018, MDH 2020 PFOS)
DAF = Vd (L/kg) x (Ln2/Half-life, days)
DAF = 0.23 L/kg x (0.693/1241 days) =
DAF = 0.00013 L/kg/d
HED = POD x DAF (mg/kg/d)
HED = 2.36 mg/L x 0.00013 L/kg/d
HED = 0.000307 mg/kg/d
Uncertainty Extrapolation
Human Variability (UFH)10
Animal to Human (UFA)3 (DAF applied)
Subchronic to Chronic (UFS)1
LOAEL to NOAEL (UFL)1
Database (UFD)3
Total Composite (UFT)100
RfD = HED/UFT (mg/kg/d)RfD = HED/UFT (mg/kg/d)
RfD = 0.000307 mg/kg-d/100
RfD = 3.1 ng/kg/d or 3.1 x 10-6 mg/kg-d
THSV = POD/UFTITSHV = 2.36 mg/L/100
ITSHV = 0.024 mg/mL
ReceptorInfant exposure via breastmilk for 1 year, from mother chronically exposed via water, followed by lifetime of exposure via drinking water. Protective for short-term, subchronic and chronic. The 95th percentile water intake rates (Table 3-1 and 3-3, USEPA 2019) or upper percentile breastmilk intake rates (Table 15-1, USEPA 2019) were used. Breast-fed infant, which is also protective of a formula-fed infant using Minnesota Department of Health Model based on Goeden (2019). Placental transfer of 40% (MDH 2020 PFOS). Breastmilk transfer of 1.7% (MDH 2020 PFOS). Human Serum half-life of 1241 days (Li et al. 2018) Volume of distribution of 0.23 L/kg (USA EPA 2016c) 95th percentile drinking water intake, consumers only, from birth to more than 21 years old (Goeden [2019]) Upper percentile (mean plus two standard deviations) breast milk intake rate (Goeden [2019]) Time-weighted average water ingestion rate from birth to 30-35 years of age (to calculate maternal serum concentration at delivery) (Goeden [2019])
Chronic Non-Cancer MCLGThe model produces a Chronic Non-Cancer MCLG of 14 ng/L (ppt). This protects health during the growth and development of a breast fed infant.

 In summary, the DPAG recommended a chronic non-cancer MCLG for PFOS of 14 ng/L to protect breast-fed infants and throughout life.

 The Board is proposing to set the MCLG for PFOS at the DPAG recommended level of 14 ng/L.

PFOS—occurrence data

 Table 10 is a summary of occurrence data for PFOS. The data includes 412 results from the PFAS Sampling Plan and detect data from 23 sites under UCMR3 for a total of 435 sample results.

Table 10. PFOS Occurrence Data > MCLG of 14 ng/L

PFOS Occurrence Data > Proposed MCLG of 14 ng/L
# of sites (of 435) > MCLG23
% of sites > MCLG5.3%
Estimated # of EPs (of 3785) > MCLG200

 A review of occurrence data indicates that 23 EPs out of a total number of 435 EPs sampled exceeded the proposed MCLG for PFOS of 14 ng/L. This represents 5.3% of all EPs sampled. This exceedance rate may overestimate the exceedance rate for other PWSs in this Commonwealth that were not sampled because the occurrence data sampling predominately targeted sites near potential sources of PFAS contamination. However, the occurrence data provides the most relevant information currently available on the prevalence and levels of PFAS in PWSs in this Commonwealth. Applying the occurrence data PFOS MCLG exceedance rate (5.3%) to the total number of EPs for all applicable PWSs (3,785 EPs), it is estimated that 200 EPs will exceed the proposed MCLG of 14 ng/L.

PFOS—proposed MCL of 18 ng/L

 The Board is proposing an MCL of 18 ng/L for PFOS. The proposed MCL is based on the health effects and proposed MCLG, occurrence data, technical feasibility, and costs and benefits.

 Table 11 is a summary of occurrence data for PFOS when compared to the proposed MCL of 18 ng/L.

Table 11. PFOS Occurrence Data > MCL of 18 ng/L

PFOS Occurrence Data > Proposed MCL of 18 ng/L
# of sites (of 435) > MCL22
% of sites > MCL5.1%
Estimated # of EPs (of 3785) > MCL191

 A review of occurrence data indicates that 22 EPs out of a total number of 435 EPs sampled exceeded the proposed MCL for PFOS of 18 ng/L. This represents 5.1% of all EPs sampled. This exceedance rate may overestimate the exceedance rate for other PWSs in this Commonwealth that were not sampled because the occurrence data sampling predominately targeted sites near potential sources of PFAS contamination. However, the occurrence data provides the most relevant information currently available on the prevalence and levels of PFAS in PWSs in this Commonwealth. Applying the occurrence data PFOS MCL exceedance rate (5.1%) to the total number of EPs for all applicable PWSs (3,785 EPs), it is estimated that 191 EPs will exceed the proposed MCL of 18 ng/L.

 Following is a summary of the estimated costs and benefits associated with the proposed MCL for PFOS of 18 ng/L. Section F of this preamble presents additional information on the costs and benefits of this proposed rulemaking. Treatment cost estimates are based on the costs to install and maintain treatment for a 1 MDG treatment plant. The actual costs would be expected to be proportionally less for a treatment plant with a smaller design capacity. For example, the average design capacity for small systems is 100,000 gallons per day, which is 1/10 of 1 MGD (that is, 0.1 MGD); treatment cost estimates for a small system with a design capacity of 0.1 MGD would be 1/10 of the cost estimates presented as follows:

 • Estimated costs:

 ◦ Estimated average annual compliance monitoring costs (@ $616/EP/Quarter) = $2.7 M

 ◦ Estimated average annual treatment costs (average of GAC and IX) = $78.7 M per MGD + estimated annual performance monitoring costs = $4.2 M

 • Estimated annual treatment capital costs, annualized over 20 years at 4% interest = $248,025 per MGD per EP × 191 EPs = $47.4 M per MGD

 • Estimated annual treatment O&M costs = $31.3 M per MGD + estimated annual performance monitoring costs = $4.2 M

 • Estimated annual treatment O&M costs = $163,818 per MGD per EP × 191 EPs = $31.3 M per MGD

 • Estimated annual performance monitoring costs = $616 per sample per EP × 36 samples = $22,176 per EP × 191 EPs = $4.2 M

 ◦ Estimated total annual costs = $78.7 M per MGD in treatment costs + $6.9 M in compliance monitoring and performance monitoring costs

 • Estimated benefits:

 ◦ 93% improvement in health protection as compared to current EPA HAL of 70 ppt

 Table 12 provides a comparison of annual costs and benefits for the proposed MCL for PFOS of 18 ng/L, EPA's HAL of 70 ng/L and other values considered for the proposed MCL. Performance monitoring costs are considered part of treatment O&M costs because performance monitoring is used to make operational decisions, such as when to change out treatment media.


Table 12. PFOS Comparison of Annual Costs and Benefits

PFOA Annual Costs and Benefits Analysis
Value (ng/L)Estimated
# of EPs
(of 3,785)
> Value
Compliance Monitoring Costs (Millions) Treatment O&M Costs Treatment Capital Costs (Millions) per MGD* annualized over 20 yearsTotal Costs (Millions)% Increase in Cost Compared to HAL% Improvement in Health Protection Compared to HAL
Treatment O&M Costs (Millions) per MGD*Performance Monitoring Costs (Millions)
HAL = 7096$2.57$15.73$2.13$23.81$44.24
35148$2.64$24.25$3.28$36.71$66.8751%63%
20183$2.70$29.98$4.06$45.39$82.1386%89%
MCL = 18191$2.70$31.29$4.24$47.37$85.6094%93%
16200$2.73$32.76$4.44$49.60$89.53102%96%
15200$2.81$32.76$4.44$49.60$89.61103%98%
MCLG = 14200$2.88$32.76$4.44$49.60$89.68103%100%

 *For purposes of totaling annual costs, the costs that vary with design capacity (treatment O&M and treatment capital costs) were multiplied by a benchmark design capacity of 1 MGD.

 In evaluating the costs and benefits, the Department's goal was to provide at least a 90% reduction in adverse health effects (a 90% improvement in health protection) when compared to the HAL of 70 ng/L. This goal is consistent with several existing drinking water standards including the following standards:

 • the requirement to achieve at least a 90% inactivation of Giardia cysts using disinfection processes within a filtration plant (§ 109.202(c)(1)(ii) regarding treatment technique requirements for pathogenic bacteria, viruses and protozoan cysts);

 • the use of the 90th percentile lead and copper levels when determining compliance with the lead and copper action levels of 0.015 mg/L and 1.3 mg/L, respectively (§ 109.1102(a)), and

 • the requirement to meet the filtered water turbidity standards in 95% of measurements taken each month (§ 109.202(c)(1)(i)).

 As shown in Table 12 and Figure 2, additional improvement in public health benefits at PFOS values lower than the proposed MCL of 18 ng/L would require increasingly steep costs. For example, compared with the proposed MCL of 18 ng/L, an MCL value of 16 ng/L is estimated to achieve an additional 3% increase at an additional annual cost of approximately $3.9 million (Table 12, Figure 2), which is a rate of approximately $1.3 million in additional annual costs for every additional 1% of benefits. Compared with the HAL, the proposed MCL of 18 ng/L is estimated to achieve a 93% improvement in public health benefits at an additional annual cost of roughly $41.4 million, which is a rate of approximately $0.4 million in additional annual costs for every additional 1% of benefits.

Figure 2. Annual Total Costs and Benefits (% Health Protection Improvement) at Various PFOS levels

 For the aforementioned reasons, the Department believes that the proposed MCL for PFOS of 18 ng/L strikes a balance between the benefits (93% improvement in public health) and costs (94% increase in costs) when compared to the benefits and costs associated with meeting the HAL of 70 ng/L.

State data

 Currently, six other states have set MCLs for select PFAS, including PFOA and PFOS, as summarized in Table 13. The proposed MCLs for the Commonwealth are of comparable magnitude as the other state standards.

Table 13. PFOA and PFOS MCLs (in ng/L) from Six Other States

NYMINJNHPAMAVT
PFOA10814121420*20*
PFOS101613151820*20*

 *The MCL for MA & VT is for a group of 5 (VT) or 6 (MA) PFAS, including PFOA and PFOS (not individual contaminants).

Advisory Committee review

 The Public Water System Technical Assistance Center (TAC) Board reviewed the pre-draft proposed rulemaking on July 29, 2021, and recommended that the pre-draft rulemaking move forward to the Board as a proposed rulemaking.

References

 American Water Works Association (AWWA), 2020, ''PFAS Case Study: Cape Fear Public Utility Authority (CFPUA).''

 ASDWA, October 2020, ''Per- and Polyfluoroalkyl Substances (PFAS) and State Drinking Water Program Challenges.''

 ASDWA, October 2020, ''Technical Bulletin to Laboratories Reporting PFAS Analysis Using EPA Methods 533, 537, or 537.1.''

 ASDWA, February 2021, ''Per- and Polyfluoroalkyl Substances (PFAS) Laboratory Testing Primer for State Drinking Water Programs and Public Water Systems.''

 Buck, R.C. et al., 2011, ''Perfluoroalkyl and Polyfluoroalkyl Substance in the Environment: Terminology, Classification, and Origins,'' Integrated Environmental Assessment and Management, Vol. 7, No. 4, pp. 513—541.

 California Water Boards, October 2020, ''Perfluorooctanoic Acid (PFOA) and Perfluorooctanesulfonic Acid (PFOS)'', www.waterboards.ca.gov/drinking_water/certlic/drinkingwater/PFOA_PFOS.html

 Connecticut Water, ''What Are PFAS?'' www.ctwater.com/water-quality/what-are-pfas

 DPAG, June 2020, ''Drexel PFAS Workbook.'' https://files.dep.state.pa.us/PublicParticipation/Public%20Participation %20Center/PubPartCenterPortalFiles/Environmental%20Quality%20Board/2021/June%2015/03_PFAS%20Petition/ 01b_App%202%20Drexel%20PFAS%20Workbook%20January%202021.pdf

 DPAG, January 2021, ''Maximum Contaminant Level Goal Drinking Water Recommendations for Per- and Polyfluoroalkyl Substances (PFAS) in the Commonwealth of Pennsylvania.'' https://files.dep.state.pa.us/PublicParticipation/Public %20Participation%20Center/PubPartCenterPortalFiles/Environmental%20Quality%20Board/2021/June%2015/03_PFAS%20Petition/01a_App%201%20Drexel%20PFAS%20Report%20January%202021.pdf

 Kwiatkowski, C.F. et al., 2020, ''Scientific Basis for Managing PFAS as a Chemical Class,'' Environmental Science and Technology Letters, Vol. 7, pp. 532—543.

 Longsworth, Sarah Grace, 2020, ''Processes and Considerations for Setting State PFAS Standards,'' Environmental Council of the States.

 Massachusetts DEP, November 2020, ''310 CMR 22.00: The Massachusetts Drinking Water Regulations.''

 Michigan Administrative Code(s) for Environment, Great Lakes, and Energy—Drinking Water and Environmental Health Division, August 2020 updated, ''Supplying Water to the Public.''

 Minnesota Department of Health, ''Perfluoroalkyl Substances (PFAS)'', www.health.state.mn.us/communities/environment/hazardous/topics/pfcs.html#safelevels

 New Hampshire Department of Environmental Services, ''New Hampshire Code of Administrative Rules,'' Parts Env-Dw 705, 707, 708, 712, 800, 2021.

 New Jersey Department of Environmental Protection, March 2020, ''Ground Water Quality Standards and Maximum Contaminant Levels (MCLs) for Perfluorooctanoic Acid (PFOA) and Perfluorooctanesulfonic Acid (PFOS).''

 New York State Department of Health, July 2020, ''Maximum Contaminant Levels (MCLs).''

 Ohio Department of Health and Ohio Environmental Protection Agency, December 2019, ''Ohio Per- and Polyfluoroalkyl Substances (PFAS) Action Plan for Drinking Water.''

 PA DEP, April 2019, ''Pennsylvania Department of Environmental Protection Bureau of Safe Drinking Water PFAS Sampling Plan.''

 PA DEP, May 2021, ''Summary of Responses from Survey of Pennsylvania Accredited Laboratories for PFAS.''

 PA DEP, May 2021, ''Summary of Results for SDW Sampling Project Using EPA Method 537.1.''

 PA DEP, July 2021, ''PFAS Monitoring Costs.''

 PA DEP, July 2021, ''PFAS Treatment Survey Response Summary.''

 Post, Gloria B., August 2020, ''Recent US State and Federal Drinking Water Guidelines for Per- and Polyfluoroalkyl Substances,'' Environmental Toxicology and Chemistry, Volume 00, Number 00, pp. 1—14.

 Rosenblum, Laura and Steven C. Wendelken, November 2019, ''Method 533: Determination of Per- and Polyfluoroalkyl Substances in Drinking Water by Isotope Dilution Anion Exchange Solid Phase Extraction and Liquid Chromatography/Tandem Mass Spectrometry,'' US EPA Office of Water, EPA Document No. 815-B-19-020.

 Shoemaker, J.A. and D.R. Tettenhorst, November 2018, ''Method 537.1. Determination of Selected Per-and Polyfluorinated Alkyl Substances in Drinking Water by Solid Phase Extraction and Liquid Chromatography/Tandem Mass Spectrometry (LC/MC/MC),'' Version 1.0, US EPA Office of Research and Development, EPA Document # EPA/600/R-18/352.

 Shoemaker, J.A., P.E. Grimmett, and B.K. Boutin, September 2009, ''Method 537. Determination of Selected Perfluorinated Alkyl Acids in Drinking Water by Solid Phase Extraction and Liquid Chromatography/Tandem Mass Spectrometry (LC/MC/MC),'' Version 1.1, US EPA Office of Research and Development, EPA Document # EPA/600/R-08/092.

 US EPA, May 2016, ''Drinking Water Health Advisory for Perfluorooctanoic Acid (PFOA),'' EPA 822-R-16-005.

 US EPA, May 2016, ''Drinking Water Health Advisory for Perfluorooctane Sulfonate (PFOS),'' EPA 822-R-16-004.

 US EPA, May 2016, ''Health Effects Support Document for Perfluorooctanoic Acid (PFOA),'' EPA 822-R-16-003.

 US EPA, May 2016, ''Heath Effects Support Document for Perfluorooctane Sulfonate (PFOS),'' EPA 822-R-16-002.

 US EPA, January 2018, ''UCMR 3 Occurrence Data by State.''

 US EPA, February 2020, ''EPA PFAS Action Plan: Program Update.''

 US EPA, March 2021, ''Announcement of Final Regulatory Determinations for Contaminants on the Fourth Drinking Water Contaminant Candidate List,'' Federal Register, Vol. 86, No. 40.

 US EPA, March 2021, ''Revisions to the Unregulated Contaminant Monitoring Rule (UCMR 5) for Public Water Systems and Announcement of Public Meeting,'' Federal Register, Vol. 86, No. 46, pp. 13846-13872.

 Vermont Agency of Natural Resources, Department of Environmental Conservation, Drinking Water and Groundwater Protection Division, March 2020 updated, ''Environmental Protection Rules Chapter 21 Water Supply Rule.''

E. Summary of Regulatory Requirements

§ 109.1. Definitions

 A definition for the acronym ''CASRN—Chemical Abstracts Service Registry Number'' is proposed to be added because the CASRN numbers are included for each of the individual PFAS compounds included in the regulation.

 A definition for ''GAC—Granular Activated Carbon'' is proposed to be added because GAC is one of the treatment technologies considered acceptable for PFAS removal.

 A definition for ''MCLG—Maximum Contaminant Level Goal'' is proposed to be added. The definition is from 40 CFR 141.2 (relating to definitions) with added text referencing MCLGs established under both the Federal and State acts.

 The acronym ''MDL'' is proposed to be added to the existing definition ''Method detection limit'' with the amended definition alphabetically reordered. The definition for ''Method detection limit'' is also proposed to be amended to be consistent with the current definition in the Federal regulations at 40 CFR Part 136 Appendix B (relating to definition and procedure for the determination of the method detection limit—revision 2).

 A definition for ''MRL—Minimum reporting level'' is proposed to be added.

 Definitions for the following acronyms are proposed to be added: ''PFAS,'' ''PFOA'' and ''PFOS.'' Definitions for individual compounds include the CASRN number to eliminate confusion as to the specific chemical form that is included in the regulation.

 A definition for ''Performance Evaluation Sample'' is proposed to be added to be consistent with Federal language.

 The existing definition for ''Reliably and consistently below the MCL'' is proposed to be amended to add ''PFAS'' defined as less than 80% of the MCL.

§ 109.202. State MCLs, MRDLs and treatment technique requirements

 Proposed subsection (a)(4) for ''Other MCLs'' would add MCLs and MCLGs for PFOA and PFOS, with an effective date of the publication of the final-form rulemaking. The MCLs and MCLGs are listed in both milligrams per liter (mg/L), which are the traditional units for MCLs, as well as in nanograms per liter (ng/L) for clarity, since the numbers are so low.

§ 109.301. General monitoring requirements

 The duplicated text in paragraph (2)(iv) through (iii) regarding performance monitoring for unfiltered surface water and GUDI, which was inadvertently added following the last regulatory update at 48 Pa.B. 4974 (August 18, 2018), is proposed to be deleted.

 Paragraph (6)(vii)(A)(I) and (II) are proposed to be amended for consistency with existing definitions that were amended in 2018 and to clarify that the Zone I and Zone II wellhead protection areas and the Zone A and Zone B surface water intake protection areas are defined in § 109.1 (relating to definitions). The proposed amendments would apply to waivers issued for synthetic organic chemicals (SOCs).

 Paragraph (8)(iii) is proposed to be amended to clarify that consecutive water systems may be exempt from PFAS monitoring, in addition to VOCs, SOCs, IOCs and radionuclides.

 Paragraph (9) is proposed to be amended to clarify monitoring requirements for point-of-entry (POE) devices. A POE device is installed on the service line to a house, building or other facility for the purpose of reducing contaminants in the water distributed to that property and is used as an alternative to centralized water treatment. POE devices must meet design and construction standards and may only be used as a treatment option by very small PWSs that serve 100 or fewer people for treating sources that were permitted prior to 1992; the POE device must be installed on every connection unless the PWS can demonstrate that water provided to a service connection meets water quality standards. See 25 Pa. Code § 109.612 (relating to POE devices). As a result, POE devices are often not cost effective and currently there are no PWSs in this Commonwealth that have a permit for POE devices. However, the Commonwealth is required to maintain requirements for POE devices to comply with Federal safe drinking water requirements. Consequently, monitoring requirements for POE devices are proposed to be added for PFAS, as well as additional contaminants, as applicable, to correct the omission of paragraphs (10)—(15) and Subchapter K (relating to lead and copper). These requirements should have been added in previous rulemakings but were mistakenly overlooked due to no PWSs in this Commonwealth having a permit for POE devices.

 Paragraph (11) is proposed to be amended to clarify that for EPs that do not provide water continuously, monitoring for PFAS is not required during quarters when water is not provided to the public.

 Paragraph (15)(i) and (ii) are proposed to be amended to clarify monitoring for PFAS for reserve EPs and EPs that receive water from a reserve source.

 Proposed paragraph (16) describes new monitoring requirements for PFAS for community water systems and nontransient noncommunity water systems. Throughout paragraph (16), the proposed provisions utilize terms of art and phrasing that mirror Federal safe drinking water regulations and are consistent with language used throughout the Department's safe drinking water regulations in Chapter 109.

 Proposed paragraph (16)(i)(A)—(C) specify the initial monitoring requirements for PFAS. Initial monitoring consists of four consecutive quarterly samples at each EP, beginning January 1, 2024, for systems serving more than 350 persons and beginning January 1, 2025, for systems serving 350 or fewer persons.

 Proposed paragraph (16)(ii)(A)—(C) specify the repeat monitoring requirements for EPs at which at least one of the PFAS with an MCL established under § 109.202(a)(4) is detected at a level equal to or greater than its MRL as defined in § 109.304(f) (relating to analytical requirements).

 Proposed paragraph (16)(iii) specifies the repeat monitoring requirements for EPs at which none of the PFAS with an MCL established under § 109.202(a)(4) are detected during initial monitoring.

 Proposed paragraph (16)(iv) specifies the repeat monitoring requirements for EPs at which at least one of the PFAS with an MCL established under § 109.202(a)(4) exceeds its corresponding MCL.

 Proposed paragraph (16)(v) requires collection of confirmation samples for each PFAS detected in exceedance of its MCL and the timing for collection of confirmation samples.

 Proposed paragraph (16)(vi) specifies the repeat and performance monitoring requirements for EPs with PFAS removal treatment.

 Proposed paragraph (16)(vii) describes the process by which systems may be able to obtain a monitoring waiver for PFAS. Systems using groundwater or groundwater under the direct influence of surface water monitoring under § 109.301(16)(ii) (relating to general monitoring requirements) may apply for a use waiver for EPs with 3 consecutive years or quarterly or annual samples with no detection of any PFAS with an MCL established under § 109.202(a)(4).

 Proposed paragraph (16)(viii) specifies when PFAS samples may be invalidated and utilizes the term ''obvious sampling errors'' consistent with 40 CFR 141.24(f)(13) and (h)(9) (relating to organic chemicals, sampling and analytical requirements).

 Proposed paragraph (16)(ix) specifies how compliance with the PFAS MCLs is determined.

§ 109.303. Sampling requirements

 Subsection (a)(4) is proposed to be amended to delete an incorrect cross reference to § 109.302(f) regarding special monitoring requirements. The special monitoring requirements under § 109.302(f) relate to groundwater under the direct influence of surface water and are taken from the collection facilities (raw source water) and not the EP to the distribution system.

 Proposed subsection (a)(6) specifies the sampling requirements for PFAS. Samples must be collected at the EP and be representative of each source during normal operating conditions. Samples must be collected by a properly trained sample collector.

§ 109.304. Analytical requirements

 Proposed subsection (f) specifies the analytical requirements for the PFAS with an MCL.

 Proposed subsection (f)(1) specifies acceptable analytical methods and MRLs. The MRLs for PFOA and PFOS are set at 5 ng/L. This level was determined through the survey conducted by the Department of laboratories accredited by this Commonwealth for PFAS analysis. It was determined using the Department's experience with laboratories finding a balance between reporting to a low level and still meeting all method required quality control.

 Proposed subsection (f)(2) specifies the requirement that analysis must be conducted by a laboratory accredited by the Department.

 Proposed subsection (f)(3) specifies the requirement for laboratories to determine MDLs for each analyte.

 Proposed subsection (f)(4) specifies the requirements for laboratories to analyze performance evaluation samples at least annually.

 Proposed subsection (f)(5) requires that the MRL must be contained within the range of calibration.

§ 109.411. Content of a public notice

 Subsection (e)(1) is proposed to be amended for formatting purposes to place the existing requirement to use the health effects language for fluoride in each Tier 2 public notice into a separate subparagraph.

 Proposed subsection (e)(1)(i) includes the relocated requirement to use the health effects language for fluoride, which was previously included in § 109.411(e)(1) (relating to content of a public notice).

 Proposed subsection (e)(1)(ii) and (iii) add the requirement to include the health effects language for PFOA or PFOS in each Tier 2 public notice for violation of the respective primary MCL, and includes the health effects language that must be used.

§ 109.416. CCR requirements

 Proposed paragraph (3.1) adds consumer confidence report (CCR) reporting requirements for PFAS with an MCL.

 Proposed paragraph (3.1)(i)(A)—(G) specify the information on detected results that must be reported.

 Proposed paragraph (3.1)(ii) requires that the respective health effects language in § 109.411(e)(1)(ii) and (iii) must be included for violation of a primary MCL for PFOA or PFOS.

§ 109.503. Public water systems construction permits

 Proposed subsection (a)(1)(iii)(D)(XIV.1) would add new source sampling requirements for PFAS.

§ 109.602. Acceptable design

 Proposed subsection (j) identifies treatment technologies considered acceptable by the Department for compliance with the PFAS MCLs.

§ 109.701. Reporting and recordkeeping

 Subsection (a)(3)(ii) is proposed to be amended to clarify that 1-hour reporting is required when a sample result requires collection of a confirmation or check sample. The word ''confirmation'' is proposed to be added because the terms ''check'' and ''confirmation sample'' are often used interchangeably but each are used in different locations in § 109.301. Under proposed § 109.301(16)(v), a confirmation sample shall be collected when PFAS is detected in exceedance of its respective MCL.

§ 109.1003. Monitoring requirements

 The proposed provisions for this section utilize terms of art and phrasing that mirror Federal safe drinking water regulations and are consistent with language used throughout the Department's safe drinking water regulations in Chapter 109.

 Proposed subsection (a)(1)(xv) identifies the PFAS monitoring requirements for bottled, vended, retail and bulk (BVRB) water systems. Compliance monitoring for all BVRB systems begins January 1, 2024.

 Proposed subsection (a)(1)(xv)(A) identifies the PFAS monitoring exemption for BVRB systems that obtain finished water from another permitted public water system.

 Proposed subsection (a)(1)(xv)(B) identifies the initial PFAS monitoring requirements for BVRB systems. Initial monitoring consists of 4 consecutive quarters at each entry point.

 Proposed subsection (a)(1)(xv)(C)(I) and (II) identify the repeat PFAS monitoring requirements for BVRB systems.

 Proposed subsection (a)(1)(xv)(D) identifies the confirmation sampling requirements for PFAS monitoring for BVRB systems that detect a PFAS in exceedance of its MCL during annual monitoring.

 Proposed subsection (a)(1)(xv)(E) identifies the repeat and performance PFAS monitoring requirements for BVRB systems with PFAS removal treatment.

 Proposed subsection (a)(1)(xv)(F)(I) and (II) specify when PFAS samples may be invalidated for BVRB systems and utilize the term ''obvious sampling errors'' consistent with 40 CFR 141.24(f)(13) and (h)(9).

 Proposed subsection (a)(1)(xv)(G) identifies how compliance with the PFAS MCLs is determined for BVRB systems.

 Subsection (b)(3) is proposed to be amended to clarify that sampling and analysis for PFAS must be in accordance with the requirements in § 109.304.

 Subsection (b)(6) is proposed to be amended to delete language that is also in subsection (b)(3), and to add the requirement that compliance monitoring samples for PFAS for BVRB systems must be collected by a properly trained sample collector.

§ 109.1403. Monitoring waiver fees

 Subsection (a) is proposed to be amended to add a PFAS use waiver fee of $100.

F. Benefits, Costs and Compliance

Benefits

 The proposed PFOA and PFOS MCLs will apply to all 3,117 community, nontransient noncommunity and BVRB water systems in this Commonwealth. Of these, 1,905 are community water systems, serving a combined population of approximately 11.4 million Pennsylvanians. Another 1,096 are nontransient noncommunity water systems serving approximately 507,000 persons.

 The benefits associated with reductions of PFOA and PFOS in drinking water arise from a reduction in adverse human health effects. Exposure to PFOA is associated with adverse developmental effects (including neurobehavioral and skeletal effects) and exposure to PFOS is associated with adverse immune system impacts (including immune suppression). Benefits may also be derived from customer actions to avoid exposure, such as a customer's purchase of bottled water or the installation and operation of home water treatment systems.

 The benefits of proposed MCLs can be presented as a percent improvement in public health protection as compared to EPA's HAL of 70 ng/L. Table 14 includes a summary of the percent improvement in public health protection for PFOA and PFOS at several levels.

Table 14. Percent Improvement in Health Protection as Compared to EPA's HAL

PFOA PFOS
Various Levels (ng/L)Percent Improvement in Health Protection as Compared to EPA HAL of 70 ng/LVarious Levels (ng/L)Percent Improvement in Health Protection as Compared to EPA HAL of 70 ng/L
3556%3563%
2080%2089%
14 (MCL)90%18 (MCL)93%
1293%1696%
1096%1598%
8 (MCLG)100%14 (MCLG)100%

 The percentage improvement in health protection values for PFOA and PFOS are based on an assumption that there is a linear improvement in health protection between the EPA HAL and the DPAG MCLG. The amount of improvement is set such that it totals 100% between the EPA HAL and the DPAG MCLG. The equation for calculating percent improvement in health protection is established as follows:

 Percent Improvement = ((EPA HAL − MCLG)-1 × 100) × (EPA HAL − Level ''X'')

 As per the DPAG MCLG Report, PFOA has the potential to disrupt human development. The most sensitive developmental effects observed include neurobehavioral and skeletal effects. It is anticipated that these developmental effects have a measurable effect on the health of infants. The proposed MCL for PFOA of 14 ng/L would be expected to improve health protection and lower the incidence of developmental effects by 90% compared with the EPA HAL of 70 ng/L.

 The DPAG MCLG Report also found that PFOS has the potential to disrupt the immune system. The effects of immune suppression are anticipated to reduce the ability to resist infections, potentially increasing the risk, duration and severity of diseases. These immune effects from PFOS have a substantial effect on the health and economy of this Commonwealth. The proposed MCL for PFOS of 18 ng/L would be expected to improve health protection and lower the incidence of immune suppression effects by 93% compared with the EPA HAL of 70 ng/L.

Compliance monitoring costs

 Compliance monitoring cost estimates for this proposed rulemaking were determined based on a survey conducted of laboratories accredited in this Commonwealth for PFAS analysis by one or more of the analytical methods in this proposed rulemaking, as well as assumptions made based on an analysis of the occurrence data. According to lab survey results, the analytical cost for PFAS by either EPA Method 533, EPA Method 537 version 1.1 or EPA Method 537.1 varied greatly among the labs that responded, with a range of $325 to $750, and an average of $516, including the cost of analysis of the associated field reagent blank required by the methods for each sample site. This does not include an additional fee for sample collection, which also varied greatly among the labs offering that service; sample collection is approximately an additional $200 based on the survey.

 Approximately half of the responding laboratories noted that they offer a cost reduction for reporting of fewer analytes than included in the method, which would provide a cost savings for systems since monitoring is required for only two analytes—PFOA and PFOS. Also, a few labs noted potential savings if there are no detections in the sample; the associated field blank would be extracted, but would not need to be analyzed, which would reduce the overall cost. A few labs also noted potential additional fees for PFAS-free blank water, overnight shipping costs for samples and Level 4 data reports if requested.

 For compliance monitoring cost estimates, it was assumed that approximately half of all water systems will collect their own samples and half will utilize sample collection services provided by the laboratory. Therefore, an average cost of $616 per sample was used in the following compliance monitoring cost estimate calculations.

 In this proposed rulemaking, initial quarterly monitoring for community and nontransient noncommunity systems serving a population of more than 350 persons begins January 1, 2024, and initial quarterly monitoring for community and nontransient noncommunity systems serving 350 or fewer persons begins January 1, 2025. This population breakdown was selected to evenly split initial monitoring across 2 years to ease laboratory capacity issues and allow small systems more time to prepare for compliance monitoring. Initial monitoring for BVRB systems begins January 1, 2024. Based on the number of PWSs and EPs in the Pennsylvania Drinking Water Information System (PADWIS) at the time of this proposed rulemaking, there are 1,885 EPs that will begin monitoring in year 1 (2024) and 1,900 that will conduct initial monitoring in year 2 (2025).

 This proposed rulemaking requires repeat compliance monitoring on a quarterly basis for any EPs at which either PFOA or PFOS is detected at a level above its respective minimum reporting limit (MRL), including those EPs at which one or both MCLs are exceeded. If the quarterly repeat monitoring results are reliably and consistently below the MCLs, the frequency of repeat monitoring may be reduced from quarterly monitoring to annual monitoring. Based on the occurrence data, it is assumed that up to 34.9% of all EPs will have a detection of PFOA or PFOS, or both, at or above the relevant MRL; this equates to 658 EPs of the year 1 initial systems that will need to continue quarterly repeat monitoring in year 2, and 663 EPs of the year 2 initial systems that will need to continue quarterly repeat monitoring in year 3. The remaining systems (1,227 EPs in year 1 and 1,237 EPs in year 2) were assumed to conduct annual repeat monitoring in each year following the initial monitoring, but this overestimates the repeat monitoring requirements and costs after the initial monitoring because, for EPs where initial monitoring results do not detect PFOA or PFOS, the frequency of repeat monitoring is reduced from annual to once every 3 years.

 In addition to and separate from the performance monitoring required by permit special condition, systems with EPs that exceed one or both MCLs may require treatment, which would require the system to conduct ongoing repeat compliance monitoring at least annually. Using the noncompliance rate of 7.4% from the occurrence data (as described in section D of this preamble), a total of 280 EPs are estimated to require ongoing repeat compliance monitoring: 139 EPs from initial year 1 and 141 EPs from initial year 2. However, this is likely an overestimate because: (1) systems may have options other than installing treatment to address concentrations of PFOA or PFOS, or both, above the relevant MCL; and (2) the occurrence data sampling predominately targeted sites near potential sources of PFAS contamination, so the exceedance rate in the occurrence data may overestimate the exceedance rate for other PWSs in this Commonwealth that were not included in the occurrence data. For total compliance monitoring cost estimates, the ongoing annual compliance monitoring for EPs where treatment is installed was assumed to begin in the third year of monitoring (year 3 or year 4 overall).

 Using these assumptions (which likely overestimate the compliance monitoring requirements and costs for the reasons described previously) and an estimated average cost of $616 per sample, Table 15 summarizes the overall cost estimates for compliance monitoring costs in each of the first four years of rule implementation. Note that this estimate does not include performance monitoring costs.


Table 15. Compliance Monitoring Costs

Total # EPsQuarterly Initial EPsAnnual Repeat EPsQuarterly repeat EPsQuarterly compliance monitoring costAnnual compliance monitoring costTotal yearly compliance monitoring cost
Year 11885188500$4,644,640$0$4,644,640
Year 2190019001227658$6,302,579$755,915$7,058,495
Year 303122663$1,633,878$1,923,090$3,556,969
Year 4037850$0$2,331,560$2,331,560

 Based on these estimates, the average annual monitoring costs over the first 4 years are $4,397,916. Note that this average annual compliance monitoring cost estimate of approximately $4.4 M is less than the sum of the average annual compliance monitoring cost estimates presented in section D of this preamble for PFOA ($2.9 M) and PFOS ($2.7 M). The reason for this difference in the average annual compliance monitoring cost estimates when considered for each individual contaminant (that is, PFOA and PFOS separately) compared with both contaminants together is that exceedances of the proposed PFOA and PFOS MCLs are expected to co-occur at some sites. For instance, the occurrence data showed exceedance rates of the individual proposed MCLs for PFOA and PFOS of 5.7% and 5.1%, respectively; however, the exceedance rate for the proposed MCLs accounting for co-occurring exceedances was only 7.4% (not 10.8%, the sum of the exceedance rates for the proposed MCLs considered individually). Since the laboratory analytical methods include both PFOA and PFOS, systems with exceedances of both proposed MCLs will not have to collect separate samples for PFOA and PFOS, which results in some reduction in compliance monitoring costs for these systems compared with if each contaminant is considered separately. However, because PFOA and PFOS are each associated with different health effects and have different recommended MCLGs, the compliance monitoring cost estimates are presented separately for each contaminant in section D of this preamble to inform the cost-benefit analysis for each MCL.

Treatment costs

 Treatment cost estimates were determined based on a survey conducted of systems in this Commonwealth with existing PFAS treatment and of PFAS treatment manufacturers, an American Water Works Association published PFAS Case Study, and from information provided by members of the ASDWA. Costs were provided for GAC, IX and RO. The RO costs were not included in the final cost estimates because, due to wastewater disposal requirements, the technology is currently impractical. Additionally, the costs for GAC, IX, and RO provided from the vendors were excluded from the final cost estimates because they were limited to media costs and did not include the infrastructure requirements.

 GAC and IX construction costs were based on a lead lag configuration where the first vessel (lead vessel) is capable of treating the entire flow and second vessel (lag vessel) is provided for polishing.

 Treatment costs were normalized to construction costs for treating 1 MGD. As shown in Table 16, the average capital cost for the GAC treatment was $3,457,110 per MGD per EP with an average annual O&M cost of $171,970 per MGD per EP.

Table 16. GAC Treatment Costs

TreatmentSystemCapital Cost
per MGD
per EP
Annual O&M Cost
per MGD
per EP
GACVendor A$343,000 *$32,018
GACVendor B$535,000 *$356,000
GACSystem A (2 GAC and 1 IX)$3,125,000 $107,007
GACSystem B, Site 1$1,675,347 $121,528
GACSystem B, Site 2$2,454,259 $220,820
GACSystem B, Site 3$2,433,333 $194,444
GACSystem C$9,250,000 unknown
GACSystem D$3,139,000 unknown
GACSystem E$1,135,497 unknown
GACSystem F$4,444,444unknown
Average cost of GAC per MGD per EP$3,457,110$171,970

 * Not included in calculations

 As shown in Table 17, the average capital cost for the IX treatment was $3,284,360 per MGD per EP with an average annual O&M cost of $155,666 per MGD per EP.

Table 17. IX Treatment Costs

TreatmentSystemCapital Cost
per MGD
per EP
Annual O&M Cost
per MGD
per EP
IXVendor A$357,000 *$59,361 *
IXVendor B$500,000 *$175,000
IXVendor DNo information$159,722
IXSystem G$10,400,000 unknown
IXSystem H$3,333,000 unknown
IXSystem I $634,900 unknown
IXSystem J$1,128,000 unknown
IXSystem K$925,900 $132,275
Average cost of IX per MGD per EP$3,284,360 $155,666

 * Not included in calculations

 The average capital costs of the GAC and IX treatment is $3,370,735 per MGD per EP with an average annual O&M costs $163,818 per MGD per EP.

 To estimate annual treatment costs, the average capital cost of treatment installation of $3,370,735 per MGD per EP was annualized over 20 years at a 4% interest rate. This yields an estimated annualized capital cost of $248,025 per MGD per EP.

 In addition, water systems that install treatment will need to conduct performance monitoring, to verify treatment efficacy. Using the average cost per sample of $616 and assuming a total of 36 performance monitoring samples per year—monthly samples at each of three locations (raw water, mid-point of treatment and finished water)—that is an additional annual cost of $22,176 per EP.

 In the occurrence data, the percentage of EPs exceeding the proposed MCLs for PFOA and PFOS was 5.7% and 5.1%, respectively; however, due to co-occurrence of PFOA and PFOS, some EPs that exceeded the proposed MCL for PFOA also exceeded the proposed MCL for PFOS. In the occurrence data, the percentage of EPs exceeding the proposed MCL for PFOA or the proposed MCL for PFOS, or both, was 7.4%. However, this exceedance rate may overestimate the exceedance rate for the other PWSs in this Commonwealth that were not sampled, because the occurrence data sampling predominately targeted sites near potential sources of PFAS contamination. Also, as treatment for PFOA and PFOS is the same, EPs exceeding both MCLs would not be required to install two different treatment systems; therefore, the estimated percentage of EPs requiring treatment is less than the combined percentage of systems exceeding either MCL in the occurrence data. Additionally, systems with MCL exceedances may have several options to address the contamination aside from installing treatment, including taking contaminated sources offline, making operational changes such as blending sources, or using alternate sources of supply (developing new sources or using purchased sources from a new interconnect). Recognizing that the MCL exceedance rates from the occurrence data may overestimate the proportion of systems that will need to install treatment to address MCL exceedances for the aforementioned reasons, the occurrence data provides the most relevant information currently available on the prevalence and levels of PFAS in PWSs in this Commonwealth. Using the 7.4% exceedance rate from the occurrence data to estimate how many of the larger universe of 3,785 EPs may require treatment to meet one or both proposed MCLs produces an estimate of 280 EPs. At an average annualized treatment capital cost of $248,025 per MGD per EP, and assuming 280 EPs require treatment installed, the total estimated annual treatment costs are shown in Table 18.

Table 18. Total Estimated Annual Treatment Costs

Estimated average annualized treatment capital costs (per MGD per EP)$248,025
Estimated average annual treatment O&M costs (per MGD per EP)$163,818
Estimated average annual treatment capital + O&M costs (per MGD per EP)$411,843
Estimated annual performance monitoring costs (per EP)$22,167
Estimated # of EPs (of 3,785) that require treatment for one or both MCLs280
Total estimated average annual treatment capital + O&M costs (per MGD)$115,316,040
Total estimated annual performance monitoring costs$6,206,760

Compliance assistance plan

 The Department's Safe Drinking Water Program utilizes Pennsylvania Infrastructure Investment Authority (PENNVEST) programs to offer financial assistance to eligible PWSs. This assistance is in the form of a low-interest loan, with some augmenting grant funds for hardship cases. Eligibility is based upon factors such as public health impact, compliance necessity and project/operational affordability.

 In addition to the standard funding mentioned previously, PENNVEST approved an additional funding program in 2021 under authority of the act of November 27, 2019 (P.L. 695, No. 101). The PENNVEST PFAS Remediation Program is designed as an annual funding opportunity to aid in the remediation and elimination of PFAS in PWSs. In 2021, approximately $25 million was made available for this grant program.

 The Department's Safe Drinking Water Program has established a network of regional and Central Office training staff that is responsive to identifiable training needs. The target audience in need of training may be either program staff or the regulated community.

 In addition to this network of training staff, the Department's Bureau of Safe Drinking Water has staff dedicated to providing both training and technical outreach support services to PWS owners and operators. The Department's web site also provides timely and useful information for treatment plant operators.

Paperwork requirements

 No new forms are required for implementation of the proposed amendments.

G. Sunset Review

 This proposed rulemaking will be reviewed in accordance with the sunset review schedule published by the Department to determine whether the regulations effectively fulfill the goals for which they were intended.

H. Regulatory Review

 Under section 5(a) of the Regulatory Review Act (71 P.S. § 745.5(a)), on February 15, 2022, the Department submitted a copy of this proposed rulemaking and a copy of a Regulatory Analysis Form to the Independent Regulatory Review Commission (IRRC) and to the Chairpersons of the House and Senate Environmental Resources and Energy Committees. A copy of this material is available to the public upon request.

 Under section 5(g) of the Regulatory Review Act, IRRC may convey any comments, recommendations or objections to this proposed rulemaking within 30 days of the close of the public comment period. The comments, recommendations or objections must specify the regulatory review criteria in section 5.2 of the Regulatory Review Act (71 P.S. § 745.5b) which have not been met. The Regulatory Review Act specifies detailed procedures for review, prior to final publication of the rulemaking, by the Department, the General Assembly, and the Governor.

I. Public Comments

 Interested persons are invited to submit written comments, suggestions or objections regarding this proposed rulemaking to the Board. The Board is seeking comments on any aspect of this proposed rulemaking, but particularly on anticipated health benefits and on the anticipated costs to comply with the proposed MCLs, including costs to design, install, and operate treatment and other remedies. Comments, suggestions or objections must be received by the Board by April 27, 2022.

 Comments may be submitted to the Board online, by e-mail, by mail or express mail as follows.

 Comments may be submitted to the Board by accessing eComment at http://www.ahs.dep.pa.gov/eComment.

 Comments may be submitted to the Board by e-mail at RegComments@pa.gov. A subject heading of this proposed rulemaking and a return name and address must be included in each transmission.

 If an acknowledgement of comments submitted online or by e-mail is not received by the sender within 2 working days, the comments should be retransmitted to the Board to ensure receipt. Comments submitted by facsimile will not be accepted.

 Written comments should be mailed to the Environmental Quality Board, P.O. Box 8477, Harrisburg, PA 17105-8477. Express mail should be sent to the Environmental Quality Board, Rachel Carson State Office Building, 16th Floor, 400 Market Street, Harrisburg, PA 17101-2301.

J. Public Hearings

 The Board will hold five virtual public hearings for the purpose of accepting comments on this proposed rulemaking. The hearings will be held as follows:

 March 21, 2022, at 1 p.m.

 March 22, 2022, at 6 p.m.

 March 23, 2022, at 1 p.m.

 March 24, 2022, at 9 a.m.

 March 25, 2022, at 9 a.m.

 Persons wishing to present testimony at a hearing must contact Jennifer Swan for the Department and the Board, (717) 783-8727 or RA-EPEQB@pa.gov, by 5 p.m. on March 18, 2022 to reserve a time to present testimony. Language interpretation services are available upon request. Persons in need of language interpretation services must contact Jennifer Swan at (717) 787-4526 by 5 p.m. on March 17, 2022.

 Oral testimony is limited to 5 minutes for each witness. Organizations are limited to designating one witness to present testimony on their behalf at one hearing. Witnesses may provide testimony by means of telephone or Internet connection. Video demonstrations and screen sharing by witnesses will not be permitted.

 Witnesses are requested to submit written copy of their verbal testimony by e-mail to RegComments@pa.gov after providing testimony at the hearing.

 Information on how to access the virtual public hearings will be available on the Board's webpage found through the Public Participation tab on the Department's web site at www.dep.pa.gov (select ''Public Participation,'' then ''Environmental Quality Board''). Prior to a hearing, individuals are encouraged to visit the Board's webpage for the most current information for accessing the hearing.

 Members of the public wishing to observe a virtual public hearing without providing testimony are also directed to access the Board's webpage. Those who have not registered with Jennifer Swan in advance as described previously will remain muted for the duration of the public hearing.

 Persons in need of accommodations as provided for in the Americans with Disabilities Act of 1990 should contact the Board at (717) 787-4526 or through the Pennsylvania Hamilton Relay Service at (800) 654-5984 (TDD) or (800) 654-5988 (voice users) to discuss how the Board may accommodate their needs.

PATRICK McDONNELL, 
Chairperson

Fiscal Note: 7-569. No fiscal impact; (8) recommends adoption.

[Continued on next Web Page]



No part of the information on this site may be reproduced for profit or sold for profit.

This material has been drawn directly from the official Pennsylvania Bulletin full text database. Due to the limitations of HTML or differences in display capabilities of different browsers, this version may differ slightly from the official printed version.