§ 139.4. References.
(a) The references referred to in this chapter are as follows:
(1) Standards of Performance for New Stationary Sources, 40 CFR Chapter I, Part 60, Appendix A, Current Edition, Superintendent of Documents, Washington, D.C. 20402-9328.
(2) National Emission Standards for Hazardous Air Pollutants, 40 CFR, Chapter I, Part 61, Appendix B, Current Edition, Superintendent of Documents, Washington, D.C. 20402-9328.
(3) Requirements for Preparation, Adoption, and Submittal of Implementation Plans, 40 CFR, Chapter I, Part 51, Appendix M, Current Edition, Superintendent of Documents, Washington, D.C. 20402-9328.
(4) Standards for the Management of Specific Hazardous Wastes and Specific Types of Hazardous Waste Management Facilities, 40 CFR, Chapter I, Part 266, Appendix IX, Current Edition, Superintendent of Documents, Washington, D.C. 20402-9328.
(5) Source Testing Manual, Commonwealth of Pennsylvania, Department of Environmental Protection, Bureau of Air Quality, Post Office Box 8468, Harrisburg, Pennsylvania 17105-8468, including future revisions as noted in § 139.5(b) (relating to revisions to the source testing manual and continuous source monitoring manual).
(6) Recommended Standard Method for Continuing Dust Fall Survey (APM-1, Revision 1), PR-2 Air Pollution Measurement Commission, J. Air Assoc., 16:372 (1966).
(7) Air Pollution Measurements of the National Air Sampling Network: Analyses of Suspended Particulates 1957-1961, Public Health Service Pub. No. 978, Washington, D.C., 1962.
(8) Interbranch Chemical Advisory Committee, Selected Methods for the Measurement of Air Pollutants, PHS Pub. No. 999-AP-11, Cincinnati, Ohio, 1965, page I-1.
(9) Standard Method of Test for Inorganic Fluoride in the Atmosphere, ASTM Standards on Methods of Atmospheric Sampling and Analyses, Philadelphia, Pennsylvania, 1962, page 67.
(10) ASTM D 4057, Practice for Manual Sampling of Petroleum and Petroleum Products, including updates and revisions.
(11) ASTM D 445, Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity), including updates and revisions.
(12) ASTM D 1266, Test Methods for Sulfur in Petroleum Products: Lamp Method, including updates and revisions.
(13) ASTM D 129, Test Methods for Sulfur in Petroleum Products: General Bomb Method, including updates and revisions.
(14) ASTM D 1552, Test Methods for Sulfur in Petroleum Products: High-Temperature Method, including updates and revisions.
(15) ASTM D 2622, Test Methods for Sulfur in Petroleum Products by X-Ray Spectrometry, including updates and revisions.
(16) Standard Methods for the Examination of Water and Wastewater, 14th Ed., Organic Carbon (total), Combustion-Infrared Method, American Public Health Association, Washington, D.C.
(17) Jacobs, M. B. et al., Ultramicrodetermination of Sulfides in Air, Anal. Chem., 29:1949 (1957).
(18) ‘‘Sampling procedures for fuel volatility,’’ 40 CFR Part 80, Appendix D (relating to sampling procedures for fuel volatility).
(19) ‘‘Tests for Determining Reid Vapor Pressure (RVP) of Gasoline and Gasoline-Oxygenate Blends,’’ 40 CFR Part 80, Appendix E (relating to test for determining Reid vapor pressure (RVP) of gasoline and gasoline-oxygenate blends).
(20) ASTM D 4294, Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry, including updates and revisions.
(21) ASTM D 4177, Practice for Automatic Sampling of Petroleum and Petroleum Products, including updates and revisions.
(b) References to ASTM in this chapter pertain to test methods developed by ASTM International, 100 Barr Harbor Drive, P. O. Box C700, West Conshohocken, PA 19428-2959, www.astm.org.
Source The provisions of this § 139.4 adopted March 3, 1972, effective March 20, 1972, 2 Pa.B. 383; amended April 27, 1979, effective August 1, 1979, 9 Pa.B. 1447; corrected May 11, 1979, effective August 1, 1979, 9 Pa.B. 1534; amended June 19, 1981, effective June 20, 1981, 11 Pa.B. 2118; amended August 12, 1983, effective August 13, 1983, 13 Pa.B. 2478; amended May 6, 1988, effective May 7, 1988, 18 Pa.B. 2098; amended May 6, 1988, effective May 7, 1988, 18 Pa.B. 2102; amended November 25, 1994, effective November 26, 1994, 24 Pa.B. 5899; amended October 31, 1997, effective November 1, 1997, 27 Pa.B. 5601; amended October 1, 1999, effective October 2, 1999, 29 Pa.B. 5089; amended June 9, 2000, effective June 10, 2000, 30 Pa.B. 2995; amended February 8, 2013, effective February 9, 2013, 43 Pa.B. 806. Immediately preceding text appears at serial pages (267065) to (267067).
Cross References This section cited in 25 Pa. Code § 139.5 (relating to revisions to the source testing manual and continuous source monitoring manual); 25 Pa. Code § 139.12 (relating to emissions of particulate matter); 25 Pa. Code § 139.13 (relating to emissions of SO2, H2S, TRS and NO2); 25 Pa. Code § 139.14 (relating to emissions of VOCs); 25 Pa. Code § 139.16 (relating to sulfur in fuel oil); 25 Pa. Code § 139.17 (relating to general requirements); and 25 Pa. Code § 139.32 (relating to sampling and analytical procedures).
No part of the information on this site may be reproduced for profit or sold for profit.
This material has been drawn directly from the official Pennsylvania Code full text database. Due to the limitations of HTML or differences in display capabilities of different browsers, this version may differ slightly from the official printed version.
